This instruction manual contains important information necessary for the proper assembly and safe use of the appliance. 5. Read and follow all warnings and.
26 pages
322 KB – 26 Pages
PAGE – 1 ============
Outdoor LP Gas Barbecue GrillModel No. GBC1932L OWNER™S MANUALTable of ContentsImportant Safeguards..Page 2 Expanded View & Hardware . 4Assembly Instructions 5Installing LP Gas Tank 9Operating Instructions 9Cleaning and Care . 10Product Registration 10Replacement Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10Limited Warranty .. 11Troubleshooting 12The use and installation must conform with local codes or, in the absence of local codes, with either the National Fuel Gas Code, ANSI Z223.1/NFPA 54, Natural Gas and Propane Installation Code, CSA B149.1, or Propane Storage and Handling Code, B149.2, or the Standard for Recreational Vehicles, ANSI A 119.2/ NFPA 1192, and CSA Z240 RV Series, Recreational Vehicle Code, as applicable .THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION . PLEASE READ AND KEEP FOR FUTURE REFERENCE.If you are assembling this unit for someone else, give this manual to them to read and save for future reference. WARNING FOR YOUR SAFETY: For Outdoor Use Only (outside any enclosure) WARNING FOR YOUR SAFETY: 1. Improper installation, adjustment, alteration, service or maintenance can cause injury or property damage. 2. Read the installation, operation, and maintenance instructions thoroughly before installing or servicing this equipment. 3. Failure to follow these instructions could result in ˜re or explosion, which could cause property damage, personal injury, or death.4. This instruction manual contains important information necessary for the proper assembly and safe use of the appliance.5. Read and follow all warnings and instructions before assembling and using the appliance.6. Follow all warnings and instructions when using the appliance.7. Keep this manual for future reference. DANGER If you smell gas -1. Shut off gas to appliance.2. Extinguish any open flame. 3. Open lid.4. If odor continues, keep away from the appliance and immediately call your gas supplier or your fire department.WARNING FOR YOUR SAFETY: 1. Do NOT store or use gasoline or other flammable liquids or vapors in the vicinity of this or any other appliance. 2. An LP cylinder not connected for use shall NOT be stored in the vicinity of this or any other appliance.DANGER Never operate this appliance unattended.Manufactured in China for: RevoAce Inc . LimitedHong Kong, China Ł 1 .800.694.0013 Ł service@revoace .com © RevoAce Inc. LimitedBlue Rhino® is a registered trademark of Ferrellgas, L .P. Used with permission. GBC1932L-ES-OM-F106Made from 75% Bagasse(environmentally friendly sugarcane pulp by-product)WARNING: This product can expose you to chemicals, including carbon monoxide, soot, lead and lead components which are known to the State of California to cause cancer, birth defects, and other reproductive harm. Wash your hands after handling this product. For more information go to www.P65Warnings.ca.gov. ¸
PAGE – 2 ============
2 WThis grill is for outdoor use only, and should not be used in a building, garage or any other enclosed area. WDo NOT operate, light or use this appliance within ten feet (3.05 m) of walls, structures or buildings. WFor residential use only. This grill is NOT for commercial use. WThis grill is not intended for and should never be used as a heater. TOXIC fumes can accumulate and cause asphyxiation. WThis grill is safety certified for use in the United States and/or Canada only. Do NOT modify for use in any other location. Modification will result in a safety hazard and will void your warranty. WThis grill is for use with liquid propane (LP) gas only. The conversion to or attempted use of natural gas in this LP gas grill is dangerous, may cause bodily harm and will void your warranty. WLP gas characteristics: a. LP gas is flammable and hazardous if handled improperly. Become aware of the characteristics before using any LP gas product. b. LP gas is explosive under pressure, heavier than air, and settles/ pools in low areas. c. LP gas in its natural state has no odor. For your safety, an odorant is added that smells like rotten cabbage. d. Contact with LP gas can cause freeze burns to skin. WApartment dwellers: Check with management to learn the requirements and fire codes for using a LP gas grill in your apartment complex. If allowed, use outside on the ground floor with a ten foot (3.05 m) clearance from any structure. Do NOT use on or under balconies. WLP gas cylinder needed to operate. Only cylinders marked fipropanefl may be used. WThe LP gas cylinder must be constructed and marked in accordance with the Specifications for LP-gas Cylinders of the U.S. Department of Transportation (D.O.T.) or the National Standard of Canada, CAN/ CSA-B339, Cylinders, Spheres and Tubes for the Transportation of Dangerous Goods; and Commission. WLP gas cylinder must be arranged for vapor withdrawal. WThe LP gas cylinder must have a listed overfilling prevention device (OPD). WOnly use LP gas cylinders equipped with a cylinder connection device compatible with the connection for outdoor cooking appliances. WThe LP gas cylinder must have a cylinder collar to protect the cylinder valve. WNever use an LP gas cylinder with a damaged body, valve, collar or footing. WDented or rusted LP gas cylinders may be hazardous and should be checked by your LP gas supplier prior to use. WThe LP gas cylinder should not be dropped or handled roughly. WLP gas cylinders must be stored outdoors out of the reach of children and must not be stored in a building, garage or any other enclosed area. Your cylinder must never be stored where temperatures can reach over 125°F. WDo NOT insert any tool or foreign object into the valve outlet or safety relief valve. You may damage the valve and cause a leak. Leaking propane may result in an explosion, fire, severe personal injury or death. WDo NOT block holes in sides or back of grill. WNever keep an LP gas cylinder in a hot car or trunk. Heat will cause the gas pressure to increase, which may open the relief valve and allow gas to escape. WPlace dust cap on cylinder valve outlet whenever the cylinder is not in use. Only install the type of dust cap on the cylinder valve outlet that is provided with the cylinder valve. Other types of caps or plugs may result in leakage of propane. WIf grill is not in use, the gas must be turned off at the supply cylinder and disconnected. WDo NOT store a spare LP gas cylinder under or near this appliance. WNever fill the cylinder beyond 80 percent full. WA fire causing serious injury or damage to property may occur if the above is not followed exactly. WNever attempt to attach this grill to the self-contained LP gas system of a camper trailer, motor home or house. WNever use charcoal, lighter fluid, lava rocks, gasoline, kerosene or alcohol with this product. WYour grill has been checked at all factory connections for leaks. Re- check all connections as described in the fiOperating Instructionsfl section, as shipping can loosen connections. WCheck for leaks even if your unit was assembled for you by someone else. WDo NOT operate if a gas leak is present. Gas leaks may cause a fire or explosion. WYou must follow all instructions in the fiChecking for Leaksfl section before operating. To prevent fire or explosion hazard when testing for a leak:a. Always perform a leak test before lighting the grill and each time the cylinder is connected for use. b. No smoking. Do NOT use or permit sources of ignition in the area while conducting a leak test. c. Conduct the leak test outdoors in a well-ventilated area. d. Do NOT use matches, lighters, or a flame to check for leaks. e. The use of alcohol, prescription or non-prescription drugs may impair the consumer™s ability to properly assemble or safely operate the appliance.f. Strong odors, colds, sinus congestion, etc. may prevent the detection of propane. Use caution and common sense when testing for leaks. g. Do NOT use grill until any and all leaks are corrected. If you are unable to stop a leak, disconnect the LP gas supply. Call a gas appliance serviceman or your local LP gas supplier. WThis grill is designed to operate at an inlet pressure of: 11 inches water column. WDo NOT store or use gasoline or other flammable liquids or vapors within 25 feet (7.62 m) of this appliance. WDo NOT use in an explosive atmosphere. Keep grill area clear and free from combustible materials, gasoline and other flammable vapors and liquids. WMinimum clearance from sides and back of unit to combustible construction is 36 inches (91.4 cm). Do NOT use this appliance under any type of overhang or roof. WIt is essential to keep the grill™s valve compartment, burners and circulating air passages clean. WInspect grill before each use. WDo NOT alter grill in any manner. Any alteration will void your warranty. WDo NOT use the grill unless it is COMPLETELY assembled and all parts are securely fastened and tightened. WDo NOT build this model of grill in any built-in or slide-in construction. Ignoring this warning could cause a fire or an explosion that can damage property and cause serious bodily injury or death. WThis grill should be thoroughly cleaned and inspected on a regular basis. WClean and inspect the hose before each use of the appliance. If there is evidence of abrasion, wear, cuts or leaks, the hose must be replaced prior to operation. WUse only the regulator and hose assembly provided. Use only the replacement regulator and hose assembly specified by RevoAce Inc. Limited WUse only RevoAce Inc. Limited factory-authorized parts. The use of any part that is not factory-authorized can be dangerous and will void your warranty. WDo NOT operate this appliance without reading fiOperating Instructionsfl in this manual. WDANGER: Failure to follow the dangers, warnings and cautions in this manual may result in serious bodily injury or death, or in a fire or an explosion causing damage to property. WWARNINGS: Important Safeguards
PAGE – 3 ============
3 WDo NOT touch metal parts of grill until they have completely cooled to avoid burns, unless you are wearing protective gear (pot holders, gloves, BBQ mittens, etc.). WDo NOT install or use in or on boats or recreational vehicles. WWhen cooking, fire extinguishing materials should be readily accessible. In the event of an oil/grease fire, do NOT attempt to extinguish with water. Use type BC dry chemical fire extinguisher or smother with dirt, sand or baking soda. WDo NOT use grill in high winds. WNever lean over the grill when lighting. WDo NOT leave a lit grill unattended. Keep children and pets away from grill at all times. WDo NOT leave grill unattended while preheating or burning off food residue on high. If grill has not been cleaned, a grease fire can occur that may damage the product. WDo NOT place empty cooking vessels on the appliance while in operation. WUse caution when placing anything on the grill while the appliance is in operation. WDo NOT attempt to move grill when in use. Allow the grill to cool before moving or storing. WLP gas cylinder must be properly disconnected and removed prior to moving this grill. WStorage of grill indoors is permissible only if the cylinder is disconnected, removed from the grill and properly stored outdoors. WAlways open grill lid carefully and slowly as heat and steam trapped within grill can cause severe burns. WDo NOT attempt to disconnect the gas regulator from the cylinder or any gas fitting while the grill is in use. WAlways place your grill on a hard, non-combustible, level surface. An asphalt or blacktop surface may not be acceptable for this purpose. WMove gas hoses as far away as possible from hot surfaces and dripping hot grease. WKeep all electrical cords away from a hot grill. WAfter a period of storage and/or nonuse, check for leaks, burner obstructions and inspect for any abrasion, wear or cuts to the hose. WFailure to open lid while igniting the grill™s burners, or not waiting 5 minutes to allow the gas to clear if the grill does not light, may result in an explosive flame-up. WNever operate grill without its heat plates installed. WAlways use a meat thermometer to ensure food is cooked to a safe temperature. WUse protective gloves when assembling this product. WNever turning the grill to high, and letting it run for a while. WDo NOT force parts together as this can result in personal injury or damage to the product. WNever cover entire cooking area with aluminum foil. Laying the foilon the grates can restrict the intended air flow inside the grill, create barriers to the proper flow of grease to the catch pan, which sets thestage for lots of it to build up on the bottom tray, which in turn, builds the potential for grease fires and flare ups. WDeaths, serious injury or damage to property may occur if the above is not followed exactly. Important Safeguards
PAGE – 4 ============
4 1224723252489220182110515171623611121314141923HardwareAScrewST4.8X10 Nickel Plated Phillips Truss Head 2 pcsBScrewM5x15 Nickel Plated Phillips Truss Head 8 pcsCScrewM6x16 Nickel Plated Phillips Truss Head 8 pcsDScrewM6x12 Nickel Plated Phillips Truss Head 4 pcsENutM8 Zinc Plated 2 pcsFWing NutM6 Nickel Plated 2 pcsGLock Washer ø6 Nickel Plated 2 pcsHWasher ø6 Nickel Plated 2 pcsISpacer ø18 x 40 Black1 pcParts List 1Warming Rack G1306-0102Cooking Grid (2)G1707-0103Heat Plate (3) B0212-0404Lid HandleG1707-0405Temperature Gauge B0104-J016Brand Plate* B0109-B027Lid*G1932-01L8Grill Body Assembly* G1932-02L9Burner (3)*G1932-03L10Light Hook*B0223-D0411Control Knob Bezel (3)* G1205-20012Control Knob (3)G0900-08013Regulator/Hose Assembly*G1306-09014Side Shelf (2)G1932-04L15Grease Cup SupportB0220-D0116Grease CupB0219-D0117Rear Cart Panel G1932-05L18LP Gas Tank Retainer WireG1932-10L19LP Gas Tank Block Wire G1932-11L20Left Cart Frame G1205-15021Front Panel G1932-08L22Right Cart Frame G1932-09L23Wheel (2)B0302-E0124AxleG1932-12L25Foot (2) G1932-07L* Pre-assembledExpanded ViewTools Required for Assembly (Included)#2 Phillips Head Screwdriver 1 pcM8 Wrench 2 pcs
PAGE – 5 ============
5 1DO NOT RETURN TO PLACE OF PURCHASE. For assistance, call 1.800.694.0013 toll-free. Please have your owner™s manual and model number available for reference.Assembly Tips: 1. Select an area where you will assemble this product. To protect components, choose a smooth surface that™s free of cracks or openings.2. Spread out all parts.3. Tighten all hardware connections by hand first . Then, before completing each step, go back and fully tighten all hardware . Be careful not to over-tighten . That could damage surfaces or strip threads.4. For best results, complete each step in the order presented .To complete assembly you will need: Ł (1) Leak detection solution (instructions on how to make the solution are included in the fiOperating Instructionsfl section of this manual).Ł (1) Precision-filled LP gas grill tank with Acme Type 1 external threaded valve connection (standard grill size) (not included) .Typical assembly is approximately one hour .Assembly Instructions4Attach Front Panel and Rear Cart Panel Bx 83Attach Axle and WheelsE x 2I x 1 BBAEI2Attach Feet Ax 2
PAGE – 9 ============
9 Installing LP Gas TankTo operate, you will need one precision-filled standard grill LP gas tank with external valve threads. WCAUTION : LP gas tank must be properly disconnected and removed prior to moving this grill.Inserting LP Gas Tank Place precision-filled LP gas tank upright into the notches in the right cart frame so the tank valve is facing the gas line connection.Securing LP Gas Tank Secure tank by sliding the tank retainer wire over shoulder of LP gas tank.Connecting LP Gas Tank 1. Before connecting, be sure there is no debris caught in the head of the LP gas tank, head of the regulator valve or in the head of the burner or burner ports . 2. Connect regulator/hose assembly to tank by turning knob clockwise until it stops . Disconnecting LP Gas Tank 1. Before disconnecting, make sure the LP gas tank valve is fiCLOSED.fl2. Disconnect regulator/hose assembly from LP gas tank by turning knob counterclockwise until it is loose . WCAUTION : LP gas tank must be properly disconnected and removed prior to moving this grill. 3. Place the protective cap cover on the LP tank and store the tank outdoors in a well ventilated area out of direct sunlight.20 lb9 Kg17.9 in. / 45.5 cm 12.2 in. / 31 cm Operating InstructionsChecking for LeaksBurner Connections1. Make sure the regulator hose and valve connections are securely fastened to the burner and the tank. 2. Visually check the connection between the burner/venturi tube and orifice. 3. Make sure the burner/venturi tube fits over the orifice. WWARNING: Failure to inspect this connection or follow these instructions could cause a fire or an explosion which can cause death, serious bodily injury or damage to property. 4. Please refer to diagram for proper installation (Figure 1) .5. If the burner/venturi tube does not rest flush to the orifice, as shown, please contact 1 .800.694.0013 for assistance.Tank/Gas Line Connection 1. Make 2-3 oz. of leak detection solution by mixing one part liquid dishwashing soap with three parts water . 2. Make sure control knobs are in the fi OFFfl position (Figure 2) .3. Connect LP gas tank per fiInstalling LP Gas Tankfl section.4. Turn LP gas tank valve to fiOPEN .fl5. Spoon several drops of solution, or use a squirt bottle, at all fiXfl locations (Figures 1 and 3) .a. If any bubbles appear, turn LP gas tank valve to fiCLOSED,fl reconnect and re-test . b. If you continue to see bubbles after several attempts, turn LP gas tank valve to fiCLOSEDfl and disconnect LP gas tank, per fiDisconnecting LP Gas Tankfl section . Contact 1.800.694.0013 for assistance.c. If no bubbles appear after one minute, turn LP gas tank valve to fiCLOSED,fl wipe away solution and proceed.Operating Main BurnersFirst Use 1. Make sure all labels, packaging and protective films have been removed from the grill . 2. Remove manufacturing oils before cooking on this grill for the first time by operating the grill for at least 15 minutes on (HIGH) with the lid closed . This will fiheat cleanfl the internal parts and dissipate odors . Lighting WCAUTION : Keep outdoor gas cooking appliance area clear and free from combustible materials, gasoline and other flammable vapors and liquids. WCAUTION : Do NOT obstruct the flow of combustion and ventilation air. WCAUTION : Check and clean burner/venturi tubes for insects and insect nests. A clogged tube can lead to a fire. WCAUTION : Attempting to light the burner with the lid closed may cause an explo sion.1. Open lid. 2. Check for obstructions of airflow to the burners . Spiders, insects and webs can clog the burner/venturi tube. A clogged burner tube can lead to a fire .3. All control knobs must be in the fi OFFfl position (Figure 2) .4. Connect LP gas tank per fiInstalling LP Gas Tankfl section .5. Turn LP gas tank valve to fiOPEN .fl6. Push and turn control knob to (HIGH). the burner should light. Repeat up to three times .7. If ignition does not occur in 5 seconds, turn burner control knob fi OFF,fl wait 5 minutes, and repeat lighting procedure . 8. If igniter does not light burner, use a lit match secured with the lighting rod (included with grill) to light burners. Access the burners through the cooking grid and heat plates . Position lit match near side of burner (Figure 4) .Figure 1 LP Gas Valve with Ori˜ceValve Soft Pipe ConnectionBurner/Venturi Tube Figure 2 OFFAPAGADO Figure 3 XXXXXFigure 4 Lighting RodMatch Figure 5 BurnerFlameSlight Yellow Slight BlueDark Blue
PAGE – 10 ============
10 Cleaning Main Burners1. Turn LP gas tank valve to fiCLOSED .fl2. Turn all control knobs clockwise to the fi OFFfl position. Note: A fipooffl sound is normal as the last of the gas is burned.3. Disconnect LP gas tank per fiDisconnecting LP Gas Tankfl section .4. Remove cooking grids and heat plates .5. Remove burners by removing the fasteners, which secure the burners to the grill bottom.6. Lift burners up and away from gas valve orifice .7. Disconnect wire from spark electrode.8. Clean venturi of each burner with small bottle brush or compressed air.9. Remove all food residue and dirt from burner surface.10. Clean any clogged ports with a stiff wire (such as an opened paper clip) .11. Inspect burners for any damage (cracks or holes) . If damage is found, replace with new burner(s) from manufacturer.12. Re-install burner(s). Checking to insure that gas valve orifice is correctly positioned inside each burner/venturi tube. Also, check position of spark electrode. 13. Replace heat plate(s) and cooking grid(s) .14. Connect LP gas tank per fiInstalling LP Gas Tankfl section.15. Perform leak test per fiChecking for Leaksfl section.Before Storing1. Turn LP gas tank valve to fiCLOSED .fl2. Turn all control knobs clockwise to the fi OFFfl position . Note: A fipooffl sound is normal as the last of the gas is burned .3. Disconnect LP gas tank per fiDisconnecting LP Gas Tankfl section .4. Clean all surfaces.5. Lightly coat the burner(s) and cooking grid(s) with cooking oil to prevent excess rusting .6. If storing the grill indoors, disconnect the LP tank per fiDisconnecting LP Gas Tankfl section .7. Place the protective cap cover on the LP tank and store the tank outdoors in a well- ventilated area out of direct sunlight .8. If storing the grill indoors, cover the grill and store in a cool dry place . 9. If storing the grill outdoors, cover the grill with a grill cover for protection from the weather .Product RegistrationFor faster warranty service, please register your product immediately . To register, call 1.800.694.0013.Replacement PartsFor replacement parts, call 1 .800.694.0013.Important: Always use the lighting rod (included) when lighting burners with a match .9. After lighting, observe the burner flame . Make sure all burner ports are lit and flame height matches illustration (Figure 5) .Note: Each burner lights independently – repeat steps 5-9 for the other burners . WCAUTION: If burner flame goes out during operation, immediately turn the control knobs to the fi OFFfl position, LP gas tank valve fiCLOSEDfl and open lid to let the gas clear for 5 minutes before re-lighting. Turning Off 1. Turn LP gas tank valve to fiCLOSED .fl2. Turn all control knobs clockwise to the fi OFFfl position . Note: A fipooffl sound is normal as the last of the LP gas is burned .3. Disconnect LP gas tank per fiDisconnecting LP Gas Tankfl section .Controlling Flare-ups WCAUTION : Putting out grease fires by only closing the lid is not possible. 1. If a grease fire develops, turn control knobs to the fi OFFfl position and LP gas tank valve fiCLOSED.fl Do NOT use water on a grease fire. This can cause the grease to splatter and could result in serious burns, bodily harm or other damage. 2. Do NOT leave grill unattended while preheating or burning off food residue on (HIGH). If grill has not been cleaned, a grease fire can occur. WWARNING: When cooking, fire extinguishing materials should be readily accessible. In the event of an oil/grease fire, use type BC dry chemical fire extinguisher or smother with dirt, sand or baking soda. Do NOT attempt to extinguish with water. Flare-ups are a part of cooking meats on a grill and add to the unique flavor of grilling .Excessive flare-ups can over-cook your food and be dangerous. Important: Excessive flare-ups result from the build-up of grease in the bottom of your grill. If a grease fire occurs , close the lid AND turn the control knob(s) to fi OFFfl until the grease burns out. Be careful when opening the lid as sudden flare-ups may occur.If excessive flare-ups occur, do NOT pour water onto the flames .Minimize Flare-ups:1. Trim excess fat from meats prior to cooking .2. Cook high fat content meats on (LOW) setting or indirectly.3. Ensure that your grill is on a hard, level, non-combustible surface and the grease is allowed to drain into grease receptacle .Cleaning and Care WCAUTION: 1. All cleaning and maintenance should be done when grill is cool and with the fuel supply disconnected.2. Do NOT clean any grill part in a self-cleaning oven. The extreme heat will damage the finish.3. Do NOT enlarge valve orifices or burner ports when cleaning the valves or burners. Notices1. This grill should be thoroughly cleaned and inspected on a regular basis. 2. Abrasive cleaners will damage this product. 3. Never use oven cleaner to clean any part of grill. Before Each Use:1. Keep the grill area clean and free from any combustible materials, gasoline, and other flammable vapors and liquids .2. Do NOT obstruct the flow of the combustion of LP gas and the ventilation of air .3. Keep the ventilation opening(s) of the LP gas tank area free and clear from debris .4. Visually check the burner flames to make sure your grill is working properly (Figure 6) .5. See sections below for proper cleaning instructions .6. Check for obstructions of airflow to the burners . Spiders, insects and webs can clog the burner/venturi tube. A clogged burner tube can lead to a fire .Cleaning Surfaces 1. Wipe surfaces clean with mild dishwashing detergent or baking soda mixed with water . 2. For stubborn surfaces, use a citrus-based degreaser and a nylon scrubbing brush .3. Rinse clean with water . 4. Allow to air dry .Operating Instructions (continued)Cleaning and Care (continued)Figure 6 Burner Flame ConditionsUse this chart to see if your burners need to be cleaned .1-2 in. / 25.4 – 50.8 mmNormal: Soft blue flames with yellow tips between 1 in. – 2 in. height.Needs cleaning: Noisy with hard blue flames.Has to be replaced: Wavy with yellow flames .
PAGE – 11 ============
11 Limited WarrantyRevoAce Inc. Limited (fimanufacturerfl) warrants to the original retail purchaser of this product, and to no other person, that if this product is assembled, maintained, and operated in accordance with the printed instructions accompanying it, then for a period of ˜ve (5) years for the burners and one (1) year for all remaining parts from the date of purchase, all parts in such product shall be free from defects in material and workmanship . Manufacturer may require reasonable proof of your date of purchase . Therefore,you should retain your sales slip or invoice. This Limited Warranty shall be limited to the repair or replacement of parts, which prove defective under normal use and service and which manufacturer shall determine in its reasonable discretion upon examination to be defective . Before returning any parts, you should contact manufacturer™s Customer Service Department using the contact information listed below . If manufacturer con˜rms, after examination, a defect covered by this Limited Warranty in any returned part, and if manufacturer approves the claim, manufacturer will replace such defective part without charge. If you return defective parts, transportation charges must be prepaid by you. manufacturer will return replacement parts to the original retail purchaser, freight or postage prepaid . This Limited Warranty does not cover any failures or operating dif˜culties due to accident, abuse, misuse, alteration, misapplication, improper installation or improper maintenance or service by you or any third party, or failure to perform normal and routine maintenance on the product as set out in this owner™s manual . In addition, the Limited Warranty does not cover damage to the ˜nish, such as scratches, dents, discoloration, rust or other weather damage, after purchase .This Limited Warranty is in lieu of all other express warranties . manufacturer disclaims all warranties for products that are purchased from sellers other than authorized retailers or distributors, including the warranty of merchantability or the warranty of ˜tness for a particular purpose. MANUFACTURER ALSO DISCLAIMS ANY AND ALL IMPLIED WARRANTIES, INCLUDING WITHOUT LIMITATION THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE . MANUFACTURER SHALL HAVE NO LIABILITY TO PURCHASER OR ANY THIRD PARTY FOR ANY SPECIAL, INDIRECT, PUNITIVE, INCIDENTAL, OR CONSEQUENTIAL DAMAGES. manufacturer further disclaims any implied or express warranty of, and assumes no responsibility for, defects in workmanship caused by third parties .This Limited Warranty gives the purchaser speci˜c legal rights; a purchaser may have other rights depending upon where he or she lives. Some jurisdictions do not allow the exclusion or limitation of special, incidental or consequential damages, or limitations on how long a warranty lasts, so the above exclusion and limitations may not apply to everyone . manufacturer does notauthorize any person or company to assume for it any other obligation or liability in connection with the sale, installation, use, removal, return, or replacement of its equipment, and no such representations are binding on manufacturer .RevoAce Inc. LimitedHong Kong, China service@revoace .com1.800.694.0013
322 KB – 26 Pages