The JamMan Solo XT is the perfect stereo looper/phrase sampler for practicing, composing, and performing. Use the JamMan Solo XT to: • Record rhythm loops then
87 KB – 72 Pages
PAGE – 2 ============
WARNING FOR YOUR PROTECTION READ THE FOLLOWING: KEEP THESE INSTRUCTIONSHEED ALL WARNINGS FOLLOW ALL INSTRUCTIONSTHE APPARATUS SHALL NOT BE EXPOSED TO DRIPPING OR SPLASHING LIQUID AND NO OBJECT FILLED WITH LIQUID, SUCH AS VASES, SHALL BE PLACED ON THE APPARATUS CLEAN ONLY WITH A DRY CLOTH. DO NOT BLOCK ANY OF THE VENTILATION OPENINGS. INSTALL IN ACCORDANCE WITH THE MANUFACTURER™S INSTRUCTIONS. DO NOT INSTALL NEAR ANY HEAT SOURCES SUCH AS RADIATORS, HEAT REGISTERS, STOVES, OR OTHER APPARATUS (INCLUDING AMPLIFIERS) THAT PRODUCE HEAT. ONLY USE ATTACHMENTS/ACCESSORIES SPECIFIED BY THE MANUFACTURER. UNPLUG THIS APPARATUS DURING LIGHTNING STORMS OR WHEN UNUSED FOR LONG PERIODS OF TIME. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or third prong are provided for your safety. If the provided plug does not ˜t your outlet, consult an electrician for replacement of the obsolete outlet.Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus. Refer all servicing to quali˜ed service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped. MAINS DISCONNECT: The plug shall remain readily operable. For rack-mount or installation where plug is not accessible, an all-pole mains switch with a contact separation of at least 3 mm in each pole shall be incorporated into the electrical installation of the rack or building.
PAGE – 3 ============
ELECTROMAGNETIC COMPATIBILITY This device complies with part 15 of the FCC Rules and the Product Speci˜cations noted on the Declaration of Conformity. Operation is subject to the following two conditions:Łthis device may not cause harmfulinterference, and Łthis device must accept any interference received, including interference that may cause undesired operation. Operation of this unit within signi˜cant electromagnetic ˜elds should be avoided.Łuse only shielded interconnecting cables.U.K. MAINS PLUG WARNING A molded mains plug that has been cut off from the cord is unsafe. Discard the mains plug at a suitable disposal facility. NEVER UNDER ANY CIRCUMSTANCES SHOULD YOU INSERT A DAMAGED OR CUT MAINS PLUG INTO A 13 AMP POWER SOCKET. Do not use the mains plug without the fuse cover in place. Replacement fuse covers can be obtained from your local retailer. Replacement fuses are 13 amps and MUST be ASTA approved to BS1362. EXTREME (RF) RADIO FREQUENCY ENVIRONMENTS The JamMan Solo XT may experience audio dropout if exposed to an Extreme RF Environment. Such RF Environments may be found in very close proximity to strong radio transmitters. If the audio is lost due to such RF Environments, it is advised that you place the ferrite choke onto the power adapter cable per the diagram below. The ferrite core (P/N 5027963) can be found within the power adapter box. Ferrite Core 12
PAGE – 4 ============
If you want to dispose this product, do not mix it with general household waste. There is a separate collection system for used electronic products in accordance with legislation that requires proper treatment, recovery and recycling.Private households in the 25 member states of the EU, in Switzerland and Norway may return their used electronic products free of charge to designated collection facilities or to a retailer (if you purchase a similar new one).For Countries not mentioned above, please contact your local authorities for a correct method of disposal.By doing so you will ensure that your disposed product undergoes the necessary treatment, recovery and recycling and thus prevent potential negative effects on the environment and human health.The symbols shown above are internationally accepted symbols that warn of potential hazards with electrical products. The lightning ˚ash with arrowpoint in an equilateral triangle means that there are dangerous voltages present within the unit. The exclamation point in an equilateral triangle indicates that it is necessary for the user to refer to the owner™s manual. These symbols warn that there are no user serviceable parts inside the unit. Do not open the unit. Do not attempt to service the unit yourself. Refer all servicing to quali˜ed personnel. Opening the chassis for any reason will void the manufacturer™s warranty. Do not get the unit wet. If liquid is spilled on the unit, shut it off immediately and take it to a dealer for service. Disconnect the unit during storms to prevent damage.
PAGE – 5 ============
DECLARATION OF CONFORMITY Manufacturer™s Name: DigiTech Manufacturer™s Address: 8760 S. Sandy Parkway Sandy, Utah 84070, USAdeclares that the product: Product name: JamMan Solo XTProduct option: all (requires Class II power adapter that conforms to the requirements of EN60065, EN60742, or equivalent.)conforms to the following Product Speci˜cations: Safety: IEC 60065 -01+Amd 1EMC: EN 55022:2006EN 55024:1998FCC Part 15Supplementary Information: The product herewith complies with the requirements of the:Low Voltage Directive 2006/95/EC EMC Directive 2004/108/EC. RoHS Directive 2002/95/EC WEEE Directive 2002/96/EC EC Regulation 278/2009With regard to Directive 2005/32/EC and EC Regulation 1275/2008 of 17 December 2008, this product is designed, produced, and classi˜ed as Professional Audio Equipment and thus is exempt from this Directive.Roger Johnsen Director, EngineeringSignal Processing 8760 S. Sandy Parkway Sandy, Utah 84070, USADate: October 24, 2012European Contact: Your local DigiTech Sales and Service Of˜ce or Harman Music Group 8760 South Sandy Parkway Sandy, Utah 84070 USA Ph: (801) 566-8800 Fax: (801) 568-7583
PAGE – 6 ============
Warranty We at DigiTech ® are very proud of our products and back-up each one we sell with the following warranty: 1. Please register online at www.digitech.com within ten days of purchase to validate this warranty. This warranty is valid only in the United States. 2. DigiTech warrants this product, when purchased new from an authorized U.S. DigiTech dealer and used solely within the U.S., to be free from defects in materials and workmanship under normal use and service. This warranty is valid to the original purchaser only and is non-transferable. 3. DigiTech liability under this warranty is limited to repairing or replacing defective materials that show evidence of defect, provided the product is returned to DigiTech WITH RETURN AUTHORIZATION, where all parts and labor will be covered up to a period of one year. A Return Authorization number may be obtained from DigiTech by telephone. The company shall not be liable for any consequential damage as a result of the product™s use in any circuit or assembly. 4. Proof-of-purchase is considered to be the responsibility of the consumer. A copy of the original purchase receipt must be provided for any warranty service. 5. DigiTech reserves the right to make changes in design, or make additions to, or improvements upon this product without incurring any obligation to install the same on products previously manufactured. 6. The consumer forfeits the benefits of this warranty if the product™s main assembly is opened and tampered with by anyone other than a certified DigiTech technician or, if the product is used with AC voltages outside of the range suggested by the manufacturer. 7. The foregoing is in lieu of all other warranties, expressed or implied, and DigiTech neither assumes nor authorizes any person to assume any obligation or liability in connection with the sale of this product. In no event shall DigiTech or its dealers be liable for special or consequential damages or from any delay in the performance of this warranty due to causes beyond their control. NOTE: The information contained in this manual is subject to change at any time without noti˜cation. Some information contained in this manual may also be inaccurate due to undocumented changes in the product or operating system since this version of the manual was completed. The information contained in this version of the owner™s manual supersedes all previous versions.
PAGE – 8 ============
2Introduction Congratulations and thank you for purchasing the JamMan ® Solo XT Stereo Looper/ Phrase Sampler. The JamMan Solo XT features 200 internal memory locations that can hold up to 35 minutes of loops. Installing a Micro SD/SDHC card into the memory card slot adds another 200 memory locations which can store over 32 hours of loops!The JamMan Solo XT has all the same great features which made up the original JamMan Solo and adds stereo looping, Micro SD/SDHC compatible memory card support, Auto Record, selectable Stop Modes, as well as the exciting new JamSync feature which allows for syncing of multiple JamSync compatible devices. The JamMan Solo XT has USB connectivity for syncing to DigiTech™s free JamManagerŽ XT software. JamManager XT organizes and saves your loops to a computer (PC or Mac) and lets you quickly create JamLists to take to your gig. The JamMan Solo XT is the perfect stereo looper/phrase sampler for practicing, composing, and performing. Use the JamMan Solo XT to: Ł Record rhythm loops then solo over them on the ˚y, completely Hands-FreeŽ. Ł Slow down or speed up the tempo of any loop without changing pitch. Ł Sync multiple JamSync compatible JamMan ® devices for multi-track looping capabilities. Ł Seamlessly transition between recorded loops during playback.
PAGE – 9 ============
3Features Ł Single Phrase & Loop PlaybackŁ JamMan® JamSync Supports Syncing of multiple JamMan Solo XTs for Multi- Track Looping Ł Stereo 44.1 kHz 16-Bit .wav File Format Ł 35 Minutes of Built-In Loop Memory StorageŁ 200 Internal Loop MemoriesŁ Compatible with Optional Micro SD/SDHC Memory Cards up to 32GB Ł 200 External Loop Memories Using Optional Memory Card Ł Selectable Time Signature Ł Tap Tempo Ł 9 Built-In Rhythm Guide PatternsŁ Auto Record SensingŁ Auto QuantizationŁ Time StretchingŁ Reverse Loop Playback Ł 3 Selectable Stop ModesŁ Stereo 1/4fl Inputs & OutputsŁ 1/8fl Stereo Auxiliary Input Ł Footswitch Jack for Optional FS3X Footswitch Ł Mini-B USB Jack for File Transfer Using JamManagerŽ XT Loop Librarian Software for Mac & PC Ł Included Power Supply Included ItemsŁ JamMan® Solo XT Stereo Looper/Phrase Sampler Ł Power Supply Ł Manual
PAGE – 10 ============
4User Interface & Connectors JAMSYNC 203941568 721. PEDAL SWITCH The Pedal Switch is used to start recording and toggle between playback and overdubbing. The Pedal Switch can also be used for tapping in tempo for a new loop, as well as undoing and redoing the last overdub. Pressing the Pedal Switch two times quickly stops loop playback. This switch is also used for exiting the Setup menu and aborting the store function.STATUS LED This LED indicates status duringrecord, playback, and overdub, asdescribed below.Solid RedŒRecordFlashing RedŒArmed for record using Auto Record Solid GreenŒPlaySolid YellowŒOverdub Flashing Red/GreenŒTempo Record Count In Flashing RedŒArmed for record Flashing GreenŒArmed for playLOOP LEVEL CONTROL This knob controls the output levelof the loop.
PAGE – 11 ============
5LED DISPLAY This display shows the currentlyselected loop memory location and JamSync status. It also shows information during operational procedures and Setup menu navigation, such as displaying and editing tempo.UP/DOWN BUTTONS The up and down buttons are used for selecting loop memory locations and selecting options when navigating the Setup menu. These buttons can also be used to cue up the nextloopfor seamless on-the-fly looptransitions.LOOP LED This green LED indicates thecurrently selected memory locationisset to playback continuously when play is initiated. Loop is the defaultsetting for recorded phrases. A Loop can be converted to a Single Phrase and vice versa. When this LED is ˚ashing, the internal or external memory is busy and the memory card should not be removed. 7. SINGLE LED This yellow LED indicates the current memory location is set to playback as a Single Phrase, playing the entire phrase only once when play is initiated. A Single Phrase can be converted to a Loop and vice versa. 8. CARD MEM LED This red LED lights when selecting loop memories on an optional Micro SD/SDHC memory card. When this LED is off, loops are being selected from the JamMan Solo XT™s internal memory. 9. RHYTHM LEVEL CONTROL This knob controls the output level of the Rhythm Guide Track.
87 KB – 72 Pages