2.1 Installation. The steps and tools needed for installing a crankset on your bike will vary depending on the model of your crankset.
22 KB – 34 Pages
PAGE – 2 ============
1. Introduction 1.1 What™s in the box 12. Getting Started 2.1 Installation 2 2.2 Preparing for your ride 3 2.3 Installing and replacing batteries 4 2.3.1 Non-drive-side powermeter 5 2.3.2 Drive-side powermeters for Dura-Ace FC-9000 6 2.3.3 Drive-side powermeters for FC-Mxxxx (XT/XTR series) 7 2.4 Con˜guring your powermeter using the 4iiii App 8 2.4.1 Con˜guring in single-sided mode 9 2.4.2 Con˜guring as a dual-sided powermeter 10 2.4.3 Unlinking your dual-sided powermeter 113. Pairing 3.1. Pairing with ANT+ enabled displays 12 3.2. Pairing with Bluetooth Smart 14TABLE OF CONTENTS
PAGE – 3 ============
4. Performing a Zero O˜set 4.1. Performing a zero o˚set via ANT+ 15 4.2. How to perform zero o˚set using your 4iiii App Bluetooth Smart) 175. Advanced Features 5.1 Renaming your powermeter using the 4iiii App 19 5.2 Setting scale factor compensation values 20 5.3 Using third-party compatibility mode on Bluetooth Smart 216. Maintenance and Care 227. Troubleshooting 238. Speci˚cations 269. Warranty 2710. Contact 30TABLE OF CONTENTS
PAGE – 4 ============
1.5mm hex tool (3) Spare 1.5mm hex screws (2) CR2032 batteries PRECISION PROCrankset included with Ride Ready purchase Quick Start Guide 1 INTRODUCTION1.1 What™s in the Box? Your PRECISION PRO powermeter comes complete with the following: 1Table of Contents
PAGE – 5 ============
2.1 InstallationThe steps and tools needed for installing a crankset on your bike will vary depending on the model of your crankset. For your safety, follow the crankset manufacturer™s instructions when installing the crankset to your bike. Consult your local bike mechanic if you are not comfortable or able to follow the manufacturer™s installation instructions. Quick Tip: Accuracy is dependent on proper torque. 2 GETTING STARTED 2Table of Contents
PAGE – 6 ============
2.2 Preparing for your ride Your powermeter is delivered with a pre-installed battery and comes ready to ride. 1. Spin the crank arms four times to wake your powermeter. 2. Pair your powermeter with a compatible display unit using ANT+ and/or Bluetooth Smart. For more details, see Section 3 3. Perform a zero o˜set (some display units refer to this as calibration). For more details, see Section 4 Quick Tip: For best performance, remember to perform a zero o˜set before each ride. 2 GETTING STARTED 3Table of Contents
PAGE – 8 ============
Loosen Tighten 2.3.1 Non-drive-side powermeters To replace the battery on your non-drive-side powermeter, you will need a new CR2032 coin lithium ion battery. 2 GETTING STARTED 1. Do not pry your battery cap. To remove, twist the battery cap counterclockwise on your powermeter 2. Remove the old battery from the battery cap. To remove the battery from the cap, hold the cap by its edges and tap it against a hard surface 3. Place your battery into the cap with ‚+™ facing the white sticker inside the battery cap Quick Tip: Do not remove the white sticker inside the battery cap, it holds the metal contacts. 5Table of Contents
PAGE – 9 ============
2.3.2 Drive-side powermeters for Dura-Ace FC-9000 To replace the battery on your drive-side powermeter you will need a new CR2032 lithium ion battery and a 1.5 mm hex tool (included with your powermeter). 1. Using the supplied 1.5 mm hex tool, remove the three screws by turning counterclockwise 2. Gently push the edge of the old battery into the battery compartment and remove the battery 3. Place your new battery into the battery compartment with ‚+™ facing outwards towards you 4. Reinstall the battery cap and tighten the three screws in place using the 1.5 mm hex tool Loosen Tighten 2 GETTING STARTED 6Table of Contents
PAGE – 10 ============
2.3.3 Drive-side powermeters for FC-Mxxxx (XT/XTR series) To replace the battery on your non-drive-side powermeter, you will need a new CR2032 coin lithium ion battery. 2 GETTING STARTED Loosen Tighten 1. Do not pry your battery cap. To remove, twist the battery cap counterclockwise on your powermeter 2. Remove the old battery from the battery cap. To remove the battery from the cap, hold the cap by its edges and tap it against a hard surface 3. Place your battery into the cap with ‚+™ facing the white sticker inside the battery cap Quick Tip: Do not remove the white sticker inside the battery cap, it holds the metal contacts. 7Table of Contents
PAGE – 11 ============
2.4 Con˚guring your powermeter using the 4iiii App When your PRECISION PRO was shipped from the factory, the drive-side and non-drive-side powermeters were linked together such that they operate as a dual-sided powermeter. Your powermeter can also operate as two independent single-sided powermeters. If you want to operate your PRECISION PRO powermeter as a single-sided powermeter using only one crank arm, follow the instructions on Section 2.4. 2Additional information and settings on your PRECISION PRO can be accessed through the 4iiii app on iOS and Android devices using Bluetooth Smart. To con˚gure your PRECISION PRO powermeter in single-sided mode, follow the instructions in Section 2.4. 3To con˚gure your PRECISION PRO powermeter in dual-sided mode, follow the instructions in Section 2.4. 1 Quick Tip: Pairing is the connection between your powermeter and display units such as a bike computer, watch, or smartphone. Linking is the connection between the drive and non-drive side powermeters. Quick Tip: Connect your powermeter to the 4iiii App once a month to check for the latest ˚rmware update. If your ˚rmware requires updating, you will be prompted to upgrade. 2 GETTING STARTED 8Table of Contents
22 KB – 34 Pages