Feb 5, 2020 — Turn off the Bonaqua 500 system with the dedicated switch. • Close the JG valve between the resins bottle and the Water Tank Module 2.0. •
15 pages
34 KB – 15 Pages
PAGE – 1 ============
Version Document Title Release Date 05 Water Purification System 2.0 2020 – 02 – 14 Water Purification System 2.0 Rev. 05 – February 20 20 3 Water Purification System 2.0 Manual Water Purification System 2.0 For Enapter Systems Installation Manual Rev. 2 DECEMBER 2018
PAGE – 2 ============
Version Document Title Release Date 05 Water Purification System 2.0 2020 – 02 – 14 Water Purification System 2.0 Rev. 05 – February 20 20 4 Rev 0 5 February 20 20 Enapter Srl Registered office: Via Lavoria 56/G 56040 Crespina (PI) Italy VAT no. 13404981006 All rights reserved. No parts of this Manual may be reproduced, stored in a data retrieval system or transmitted by any means without the pri or written permission of the issuer. The following exception appl y : photocopying pages from the manual for instruction for or by lecturers is allowed. Subject to change without prior notice.
PAGE – 3 ============
Version Document Title Release Date 05 Water Purification System 2.0 2020 – 02 – 14 Water Purification System 2.0 Rev. 05 – February 20 20 5 CONTENT CONTENT .. .. .. .. 5 WELCOME .. .. .. .. .. 6 Scope of the document .. .. .. .. . 6 Approved use .. .. .. .. .. 6 PREFACE .. .. .. .. .. 7 Warnings, Hazards, Warrant y and Technical data .. .. .. .. 7 WATER PURIFICATION SYSTEM 2.0 OVERVIEW .. .. .. 8 WORKING PRINCIPLE .. .. .. 8 DATASHEETS .. .. .. 9 Bonaqua 500 .. .. .. .. 9 Miniblock 70 .. .. .. .. . 10 WATER PURIFICATION SYSTEM 2.0 INSTALLATION .. .. .. 11 Packaging .. .. .. .. .. . 11 Water connection .. .. .. .. .. 12 Electrical connection .. .. .. .. 14 Power ON .. .. .. .. .. . 14 Power OFF .. .. .. .. . 14 INTEGRATION WITH WATER TANK MODULE 2.0 .. .. .. 15 LEDS MEANING .. .. .. . 15 MAINTENANCE .. .. .. .. 15
PAGE – 4 ============
Version Document Title Release Date 05 Water Purification System 2.0 2020 – 02 – 14 Water Purification System 2.0 Rev. 05 – February 20 20 6 WELCOME Thank you for choosing the Water Purification System 2.0. Please read through this Installation Manual carefully before performing any operation. If you have any further question on the installation of the device, please contact the Enapter Srl Help Centre. Quote the system serial number when contacting us; you will find the serial number on the type plate placed on the rear side of the modules. En apter Srl Headquarters: Via di Lavoria 56/G 56040 Crespina (PI) Italy T.: +39 050 644 281 Website : www.enapter.com Scope of the document This Installation Manual provides the installer with the information needed to carry out the installation of the Wat er Purification System 2.0. The information contained in this manual will help you to install the Water Purification System 2.0 safely and as intended. Keep this Installation Manual in a safe place and readily available. Always follow its instructions. It is the Water Purification System 2.0 is always in a proper condition . Please observe any additional local requirements applicable to the installation of the Water Purification System 2.0 . Approved use The Water Purification System 2.0 has been designed to produce low – conductivity water th at can be used for the Enapter Electrolyzers . The unit must only be operated for this purpose, according to the specifications and instructions provided i n this manual and in th ose provided by BWT, included .
PAGE – 5 ============
Version Document Title Release Date 05 Water Purification System 2.0 2020 – 02 – 14 Water Purification System 2.0 Rev. 05 – February 20 20 7 Danger of injury due to improper use! Improper use of the product can result in serious injuries. Ensure that the manual is always accessible . Make sure you have read and understood this manual in its entirety. Comply with all safety instructions and warnings. Store the manual and other documentation in a safe place and pass them on to future owners o f the product. Comply with all local regulations. PREFACE Warnings , Hazards , Warranty and Technical data D o not use the Water Purification System with non – drinking water and/ or sea water or with water with a very high salt content . Do no t use the Water Purification System if clearly damaged. For other information Refer to BWT manuals included in the packaging.
PAGE – 6 ============
Version Document Title Release Date 05 Water Purification System 2.0 2020 – 02 – 14 Water Purification System 2.0 Rev. 05 – February 20 20 8 WATER PURIFICATION SYSTEM 2.0 OVERVIEW Figure 1 : Set up Overview WORKING PRINCIPLE When there is necessity of water, the produced decrease in pressure at the outlet of the system activates the pump ( located within the Reverse Osmosis system). De – ionized water starts to flow out of the machine . W hen water is not anymore required (a downstream valve is closed) , the produced increase of pressure stops the pump.
PAGE – 8 ============
Version Document Title Release Date 05 Water Purification System 2.0 2020 – 02 – 14 Water Purification System 2.0 Rev. 05 – February 20 20 10 Miniblock 70 Miniblock 70 Model 70 Max flow rate l/h 280 Min flow rate l/h 35 Max pressure bar 6 Max – Min water temperature °C 10 – 30 Max – Min ambient temperature °C 5 – 40 Cyclic capacity ppm of CaCO 3 x m 3 150 Resins liters 7 Conductivity sensor Power supply V – Hz 230 – 50/60 Max – Min water temperature °C 10 – 30 Alarm threshold uS adjustable
PAGE – 9 ============
Version Document Title Release Date 05 Water Purification System 2.0 2020 – 02 – 14 Water Purification System 2.0 Rev. 05 – February 20 20 11 Figure 2 : Components present inside the packaging WATER PURIFICATION SYSTEM 2.0 INSTALLATION Packaging also : a tube collar connector for wastewater ( for 6 mm pipe ) a 1/2 ” cap 1 2 3 4 5 6 7 8
PAGE – 10 ============
Version Document Title Release Date 05 Water Purification System 2.0 2020 – 02 – 14 Water Purification System 2.0 Rev. 05 – February 20 20 12 Water connection Required tools Water connections Plastic pipe cutter Piping and tubing Water connections: 8 mm and 6 mm Ø LLDPE pipe ( 6 bar pressure resistant) C onnections working principle 1. Cut the tube square and remove sharp edges. Ensure the outside diameter is free of score marks. 2. Push the tube into the fitting, to the tube stop. 3. Pull on the tube to check it is secure. Test the system before use. OPERATORS MUST PERFORM THE FOLLOWING ACTIONS: Be sure that the screw on the frontal panel of the Bonaqua 500 , below the red and the green leds, is fully tight (clockwise). According to your needs, use piece n. 6 or piece s n. 1 and n.5 together ( with or without cap ) , connect an 8 mm Ø LLDPE pipe to the tap. The other end of the pipe must be inserted in the together . Cut the pipe according to your site. Cutting it, please consider that you will need another 8 mm Ø LLDPE pipe from the Resins bottle to the Water Tank Module 2.0 (see Figure 1). C ut the 6 mm Ø LLDPE pipe in two pipes and connect them to the remaining ports on the rear of the Reverse Osmosis system Bonaqua 500 :
PAGE – 11 ============
Version Document Title Release Date 05 Water Purification System 2.0 2020 – 02 – 14 Water Purification System 2.0 Rev. 05 – February 20 20 13 Figure 3 : Resins bottle set up – to your wastewater system, eventually using the tube collar connector provided. – connect it to the r esins bottle inlet. As shown in Figure 3 . Connect the outlet of the resins bottle to the inlet of the Water Tank M odule 2.0 port W1.5, using an 8 mm Ø LLDPE pipe . Place right after the Resins bottle the provided 8mm John Guest valve (see Figure 1). Optionally, you can also connect the conductivity sensor to the resins tank. Use Teflon. Set the threshold for the required water quality to 5 uS/cm. Notice : the conductivity sensor led color can become red if the machine is not working for some time: it is normal. If the led is red also while providing de – ionized water, it means the resins are exhausted and they must be changed. Piece n.6 Piece n.6 Piece n. 4 Conductivity sensor
34 KB – 15 Pages